LENZE 8600 MANUAL PDF

View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. vector. System/Component overview. Lenze. FU vector en 11/ 3. System overview/Selection guide. Communication modules e.g. keypad or. PROFIBUS. Get Lenze IB Manual. Get all Lenze manuals! with optical fibre cable together with the controller series as of E DC controller E 5x. 6x.

Author: Kazrazilkree Tukazahn
Country: Ghana
Language: English (Spanish)
Genre: Travel
Published (Last): 1 February 2012
Pages: 399
PDF File Size: 10.60 Mb
ePub File Size: 13.65 Mb
ISBN: 234-3-71492-750-5
Downloads: 4279
Price: Free* [*Free Regsitration Required]
Uploader: Grolrajas

Process data description structure index 20hex.

Value Gain Adjustment of the act. Operation at rated power factory setting 8 6 0 3 8 6 0 4 3 x 2.

Don’t have manyal account? Here, the field frequency input via terminal 8 or via the digital frequency input or via code CO46 is used to limit the maximum field frequency. For the adjustment of the act.

Lenze series Manuals

Table of contents Technical Data 1 Variant Communication medium Service no. Diagnosis data The controller supplies the following diagnosis data: Parameter value or fault information in case of an invalid access.

If they are different, there is a defective. Reset Of The Diameter Compensator To activate the diameter compensator the threshold which is to be must set under C94 be decreased so that the dancer-Position controller tan be activated.

What’s missing? Tell us about it.

Adjustment of the act. Loop Control With Speed Adaption Furthermore, these Signals tan be adjusted in the best possible way by setting facilities. Freely Assignable Digital Inputs Process data can manuao divided into process output data PO data and process input data PI dataviewed from the master, that means PO data are input data for the controller.

  ELEMENTARZ HAKERA PDF

Quick stop time hex The parameter “quick stop time” corresponds lenz the relative speed ramp of the deceleration for the control commands “quick stop”, “disable ramp function generator” or the QSP terminal function.

The advantages of IO control tan be used especially for Single drives. This symbol refers to items of information intended to facilitate operation. Sensorless Diameter Detection 1. The setting is in bit-times and therefore depends on the selected baud rate.

Lenze – : DACPOL-SERVICE

Ramp Generator Input Features Of Setpoint More detailed information about the use of the parameter can be obtained from the chapter “process data configuration” page Setting Of The Controller Parameters Additional Functions Additional functions For special applications, you tan use a variety of additional functions: Additional module for the Lenze series, Slave connection module for the manua System Can be integrated into the base controllers Can be combined with the automation modules PP, Dancer-Position controller with speed and diameter Diameter mamual via analog input of the dancer-Position controller via ramp function Soft insertion generator or multiplication with the main setpoint Sensor compensator for fault and diameter corrections Torque control with Speed limitation Approvals types to VDEVDE reg.

  ETHIQUE PASTORALE PDF

These persons tan discharge themselves by touching the PE fixing screw or another grounded metal part in the control cabinet. Installation You can integrate the IB bus interface module into the controllers of the, series. Setting using manuak keypad on the controller 1. Configuration Using code CO05 you tan determine the internal control structure and the use of the setpoint and act. Lecom2 Interface option Configuration Manuall Using code CO05 you tan determine the internal control structure and the use of the setpoint and act.

Page Checking the lfnze Stage The measurements described below are to be carried out only by indicate the nominal value.

The parameter is mapped via the ramp-min function to the Lenze deceleration ramp L-C Among others, it contains defined process data. Grinding And Cutting-off Wheel Drives Ventilators, a maximum of 30s. Please note that the braking time may vary each time. Process input data description hex Data format: