ISO 16426 PDF

BRITISH STANDARD BS EN ISO Incorporating Corrigendum No. 1 Fasteners — Quality assurance system The European. Find the most up-to-date version of ISO at Engineering We are looking ISO , it was referenced in a document. The statement that can be found on it is: ISO specifies requirements for a fastener q.

Author: Nikogami Dulabar
Country: Liechtenstein
Language: English (Spanish)
Genre: Environment
Published (Last): 14 June 2010
Pages: 92
PDF File Size: 2.73 Mb
ePub File Size: 20.45 Mb
ISBN: 516-2-16468-268-5
Downloads: 47609
Price: Free* [*Free Regsitration Required]
Uploader: Kazragami

The shipping document shall include at least the designation of the fasteners and the manufacturing lot number or trace number. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. If these details are to io used for any other purpose than implementation then the prior written permission of BSI must be obtained.

Experience has shown that for one single specified characteristic, after automatic inspection there is still an average remaining level of 1646 of about. For this reason, corrosion resistance is assured by means of suitable production management measures isi in-process control.

Special measures are taken to prevent mechanical damage especially at points of impact and to avoid contamination. This does not preclude the 1646 use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If the document is revised or amended, you will be notified by email. Proceed to Checkout Continue Shopping. ISO shall not be held responsible for identifying any or all such isk rights. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

For dated references, subsequent amendments isp, or revisions of, any of these publications do not apply. These requirements are intended to reduce or prevent the production of non- conforming fasteners with the objective of approaching zero defects for the characteristics specified.

  CASA DI FOGLIE DANIELEWSKI PDF

Examples of unsystematic process characteristics are: In case of dispute, the supplier shall be able to provide all necessary information relating to the manufacturing lot number.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. For all other characteristics, the manufacturer may use the quality plan of his choice and the customer shall rely on ISO to evaluate the level of conformance of the purchased fasteners.

Additionally, the user shall take all prudent measures to assure the integrity of the fasteners purchased in accordance with this International Standard. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards.

The customer, upon opening the original packaging, assumes full responsibility for all subsequent traceability. Draft International Standards isl by the technical isso are circulated to the member bodies for voting. For undated references, the latest edition of the normative document referred to applies. Compliance with a British Standard does not of itself confer immunity from legal obligations.

Fasteners manufactured under the conditions of this International Standard shall be delivered in manufacturing lots.

ISO – Fasteners — Quality assurance system

The machines used today in the production of fasteners e. This International Standard outlines the requirements from receipt of raw material through the manufacturing process to delivery at the distributor or the user, who is the installer. To achieve this aim, intermediate objectives are set by specifying criteria for evaluating the delivered quality of fasteners.

Parts with non-conformities in measurements, geometry and other properties result from unsystematic or systematic process characteristics. The corresponding tolerances are specified considering the individual ido and production method. Endorsement notice The text of ISO We have no document history for this standard. In the manufacture of fasteners, a number of production processes are reached by means of cold forming.

BS EN ISO – Fasteners. Quality assurance system

The application of SPC cannot guarantee the delivery of fasteners with non-conformities, on a statistical basis. The BSI copyright date displayed in this document indicates when the document was last issued. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Ieo Centre has the same status as the official versions. For details of these and kso benefits contact Membership Administration.

  COMPLEJO DENTINO PULPAR PDF

BS EN ISO 16426:2002

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. The manufacturer shall be able to provide documentation for any manufacturing lot, to prove the compliance of the fasteners to the specifications, and this shall include at least: BSI offers members an individual updating io called PLUS which ensures that subscribers automatically receive the latest editions of standards.

For screws with large length: It is incorporated by Royal Charter. Please first log in with a verified email before subscribing to alerts. This is schematically illustrated in Figure A.

Revisions British Standards are updated by amendment or revision. While unsystematic non-conformities cannot be recognized by statistical process control SPCsystematic non- conformities can usually be limited by the application of SPC.

In the kilnuley evtne ttah a borpmel talerign to iwo f si,dnuo saelpfni erom teh tneCS larterceratai ta thserdda es igvne olebw. Your Alert Profile lists the documents that will be monitored.

The order shall designate the selected product characteristics, if any, considering the intended application, or a reasonably foreseeable application and its consequence. If no parts inspected are found to be non-conforming, the jso lots may be approved for delivery or use as applicable.

The same applies for the application of lubricants on fasteners to meet specified limits of coefficients of friction.