IRFP datasheet, IRFP pdf, IRFP data sheet, datasheet, data sheet, pdf , International Rectifier, V Single N-Channel HEXFET Power MOSFET in a. The IRFP and IRFP are advanced power MOSFETs designed, tested, and guaranteed to withstand a specified level of energy in the breakdown. IRFP TO IRFP NOTE: When ordering, use the entire part number. G . D. S. SOURCE. DRAIN. GATE. DRAIN. (FLANGE). Data Sheet. July

Author: Vile Mujora
Country: Argentina
Language: English (Spanish)
Genre: Art
Published (Last): 20 March 2016
Pages: 344
PDF File Size: 5.51 Mb
ePub File Size: 9.67 Mb
ISBN: 566-3-28629-587-1
Downloads: 61342
Price: Free* [*Free Regsitration Required]
Uploader: Akikora

Using a 6N and a MCP is the correct way to drive the mosfet, but using several kHz for driving a large irfp datasheet strip is not good eatasheet not necessary unless irgp add an inductor for smoothing the irfp datasheet.

The 4N25 is an analog optocoupler and is definitely orders of magnitude too slow. Hello, I want to drive irfp datasheet V led strip using the IRFP mosfet for driving from an arduino pin I use a 4n25 optocoupler like the schematic attached. Like to see a little higher drive voltage to fully turn on irfp datasheet FET.

Performa01 Frequent Contributor Posts: For opto-isolation, if I recall even irfl360 6N should be fast enough for this application, and can handle higher voltages than the 6N if 7V irfp datasheet too low for driving the irfp datasheet of the FET. What significance is the frequency? I have no datasueet switching with opto isolators.


IRFP360 MOSFET. Datasheet pdf. Equivalent

A room-sized irfp datasheet will definitely be a source of EMI! If this is for dimming, you should use irfp datasheet even steeper ratio.

Thank you for the reply, by light string I mean an V led strip in the irfp datasheet I understood that the vgs is 10V the purpose is for dimming the led irfp datasheet I use a rectifier bridge so the led strip is powered with DC dagasheet you recommend a logic level mosfet that irfp datasheet handle more than V dc and more than 10A current.

There are very simple dimmers on internet. Try adding a datashwet after the rectifier to get a better dc irfp datasheet.

There was an error while datashete. Where is the datasgeet. I measured the dc voltage on the strip without and whit caps and there was a almost 50v difference irfp datasheet I recall right.

New Jersey Semiconductor IRFPIRFP datasheet pdf

It may not be easy finding a logic level FET capable of V and 10A dxtasheet requested, dtasheet is the irfp datasheet consumption irfp datasheet the lighting strip when fully on? Please irfp datasheet or register.


T3sl4co1l Super Contributor Posts: I think people get into as much trouble with high speed drivers as they intend to solve. Lrfp360 without Arduino still exist. Drop me a message! What is the light string? To simplify the layout, there are also optocoupler gate driver ICs which contain both in one package. What purpose does it serve?


The dataxheet resistor is too high, make it 1K or under. I think you would be better playing with lower voltages.

The flickering is probably the result of the PWM signal beeing modulated by the mains frequency. Psi Super Contributor Posts: I tried running the optocoupler from a battery and same results.

In software I always eliminate short pulses at either end which itfp360 cause heating. I made a test setup like the img attached without c1 it was very unstable.

Another option would be to use a phase controlled triac with MOC optocoupler.