Provides information to enable POS operators to use the TM-. L90 safely and correctly. TM-L90 Service Manual. Describes maintenance, inspection and repair . EPSON has been taking industryinitiatives with its own POS printer . TM-L90 with Peeler User’s Manual TM-L90 peeler specification safely and correctly. Epson TM-L90 is a label printer for retail printing with receipt and greyscale printing. It also has greyscale for multi-tone printing.
|Published (Last):||24 January 2013|
|PDF File Size:||5.46 Mb|
|ePub File Size:||9.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Contact Us Submit your contact details below and an Epson expert will be in touch: Install the paper cutter cover assembly onto the cutter frame assembly. Hinge spacer Glossy surface Glossy surface Glossy surface Hinge spacer Install in the reverse sequence of removal.
TM-L90 User’s Manual (14 Languages) – Thermal line Printer – Download – POS – Epson
Remove one S1 screw, and remove the BM paper detector circuit board assembly. Got it, continue to print. Frame strengthening plate L Front frame Install in the reverse sequence of removal.
Connecting Cables Even if you can see two holes, this is the only one to put the screw in. A all pages Newly authorized Rev. Check the part shown below to see if the autocutter is set to full cut or partial cut. Remove the two head holder springs from the spring holder panel by rotating them. Avoid using alcohol, benzene, thinner, trichloroethylene, or ketone-based substances to remove dirt or foreign matter from the printer, because these substances can affect or damage plastic and rubber parts.
EPSON TM-L90 USER MANUAL Pdf Download.
Confidential Horizontal Installation Place the printer with the paper exit facing upward. Page 9 Pull the peeler open lever forward and open the peeler cover. Closing the cover unit while the movable blade is in the standby position makes the fixed blade hit the frame portion of the autocutter unit, and is set to the correct position against the movable blade.
Lubricate the two fm-l90 gear tm-l9 with G, in a line-shape. Disconnect the lead wire of the BM paper detector circuit board assembly from the switch circuit board assembly, and remove the ferrite core. Page 51 Confidential Label Paper Holder 1.
Contents of the Manual Tmm-l90 configuration of the manual is as follows. Cut the plastic sheet with a cutting tool mahual as a cutter knife. Do not make modifications to the unit. Once the printer is used, do not change the cutting method from partial cut to full cut, since the wear rate on the blades differs between the areas where the paper passes and where the paper does not, which can result in a paper-cutting problem.
Attached to the platen holder of the cover unit are the paper feed roller shaft holder, platen, cover open lever, lever shaft, lever button, fixed blade, and reflective photo detector.
nanual Confidential Cleaning the Case Use a dry cloth or lightly dampened cloth to clean the case. Remove two manual cutter screws 2. Buttons and Switches Power switch The power switch non-locking, push switch on the right part of the front face of the unit turns the printer on or off. You can clean them easily if you use a wasted label, as shown in the illustration.
Handle it with care. Confidential Electrical Specifications Operating voltage: Do not use any alcohol based solvents for cleaning.
When connecting or disconnecting the power supply from the printer, make sure the power supply is not plugged into an electrical outlet. Tabs Label paper guide 2.
It also flashes when the printer is in a wait FEED status for the button to be pressed. Not yet an Epson partner? The tightening torque for the nut should be between Practical design features, such as drop-in paper load, selectable auto-cutter and jamproof paper feeding, ensure smooth operation. Users may choose between partial cut and full cut by adjusting the autocutter unit to the desired position.
Be sure not to touch these parts. Page 81 – Adjusting the Detecting Point of the Rol After you have installed the paper holding rollers, lubricate with G at the 16 points shown below. Label and receipt paper, from 38mm to 80mm wide.
Remove reduction gear C.
Larger receipt rolls, wider paper Mabual, the TM-L90 label printer is one of the most efficient label printers available: Slide the label paper spacer to the appropriate width.
This may cause the printer to feed the following label. Remove the paper cutter cover assembly. Remove the switch circuit board assembly by spreading the two hooks of the switch panel holder. If the motor or the coils are shorted, replacing the main circuit board will not fix the problem.
Epson TM-L90 series Service Manual
Adjust the position of the cutter driving gear so that the triangle mark on the cutter driving gear becomes visible through the hole in the paper cutter cover assembly. Remove frame strengthening plate L.
Page 45 Confidential 2. Be aware that the thermal print head and its supporting parts become very hot. Epson recommends cleaning the thermal head periodically generally every 6 months to maintain receipt print quality. First Level Cable Wiring 1.