EN 50083-9 PDF

DIN EN Cable networks for television signals, sound signals and interactive services – Part 9: Interfaces for CATV/SMATV headends. Buy CEI EN CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES – PART 9: INTERFACES FOR . BS EN Cable networks for television signals, sound signals and interactive services – Interfaces for CATV/SMATV headends and similar.

Author: Nikogul Gakree
Country: Bermuda
Language: English (Spanish)
Genre: Medical
Published (Last): 17 October 2018
Pages: 126
PDF File Size: 15.70 Mb
ePub File Size: 20.88 Mb
ISBN: 812-2-25519-604-2
Downloads: 83829
Price: Free* [*Free Regsitration Required]
Uploader: Akinozshura

Switching between the code words depending 05083-9 the RD in the transmitter and receiver maintains the DC balance. Indicates valid data at the interface. Recovered serial data bits are passed to a decoder which converts the bit transmission words back into the 8-bit bytes originally transmitted. The present document also contains a recommendation clause, which provides simple measures to improve interoperability between ASI equipment.

The receiver shall present a properly aligned byte 5003-9 after the receipt of two K Electromagnetic compatibility for equipment EN Part rn The accuracy of the derived clock is dn by Amean and Asd for the frequency, and Tmean and Tsd for the time.

Data 0 to Data 7. To achieve this, the receiver clock frequency needs to be equal to or greater than the transmission clock frequency. The aperiodicity can be expressed as a short-term change in the transport rate. Additionally, an ASI input should be designed with an receiver buffer that accommodates as wide 05083-9 variety of ASI outputs as possible within appropriate commercial constraints.

These Figures reflect the result of these types of packet delivery as seen at Layer Flags are provided to distinguish byte packets from byte packets, and to signal the existence of valid RS bytes. Passive wideband equipment for coaxial cable networks EN Part 5: RD is calculated based on two subblocks: In the case of fibre-optic 500839- the serial bitstream is passed to a driver circuit which drives an LED emitter which is coupled to a fibre-optic cable through a mechanical connector.

Each transmission character in the table Valid data character is associated with a name Dx. This unidirectional optical fibre or copper coaxial cable carrying data from the transmitting node to the receiving node is referred to as a link. The present document assumes that the receiver clock is linked to the transmission clock, but is silent about how to achieve this in practice.


BS EN 50083-9:2002

The data rate is much more constant, and the required receiver buffer also is much lower. In addition references are made to all other parts of EN series Cable networks for television signals, sound signals and interactive services and in particular for RF, video and audio interfaces to part 5: EN 500833-9, EN Accept and continue Learn more about the cookies we use and how to change your settings.

This document Older versions. Transport Streams from different sources may have different ne rates.

EVS-EN 50083-9:2002

For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. The number of bytes transferred in each time slice is shown in the left curve of Figure F. This specification is similar to EN and EN Considering that the transmission data rate is derived from the user data rate, longer links can be achieved for lower user data rates. Already Subscribed to this document.

NOTE 4 For the purpose of these masks, the rise time and delay time should be measured between —0,4 V and 0,4 V, and should not exceed 4 ns. ATM is particularly suitable for providing bandwidth on demand and it allows for high data rates.

Document Status Indicators The Green document status indicator indicates that the document is: All kinds of networks like: The ASI specification allows for unlimited time displacement of data bytes.

The Red document status indicator indicates that the document is an old version The document has likely been withdrawn by the publisher, also the meta data presented here may be out of date as it is no longer being maintained by the editorial teams at NBS. Need more than one copy? The Transport Stream is designed for use in environments where errors are likely, such as storage or transmission in lossy or noisy media.


Both examples shown above highlight the fact that in an ASI design careful consideration needs to be given to the properties of the delay variation of the link. This ASI specification applies only to the point-to-point type link. Annex E gives some proposals for how such a circuit can be designed.

NOTE 4 For the purpose of these masks, the rise time and delay time should be measured between -0,04 Eb and 0,4 V, and should not exceed 4 ns. The optical characteristics of the links are described in the Table A.

The points where conformance is required are shown as point S and R in the Wn B. The link is used by the interconnected ports to perform communication. The basic unit of Layer-0 is the link.

EVS-EN – Estonian Centre for Standardisation

It’s a community-based project which helps to repair anything. On the ASI link, the bytes can be displaced in time with respect to their isochronous position.

The cable shall have a coaxial pair shall be assumed to follow an approximate maximum insertion rn of 12 dB at a frequency of 70 MHz.

Note that the loop still acquires synchronization in about samples, or 0,07 s. The physical medium specified in this subclause has the following characteristics: As the actual rate may deviate from the average, we introduce the peak rate as the highest rate found in the N time slices. The 10B transmission code is defined in terms of “disparity”, i. We have no amendments or corrections for this standard.

With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks.