Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.
|Published (Last):||16 June 2014|
|PDF File Size:||11.84 Mb|
|ePub File Size:||5.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Lock and unlock the fibers at an ambient temperature of? Optical energy does not act as an ignition source, thus there is no danger of explosion or fire. Although the bending repetition tolerance of a standard cable is approximately 13, times, robot cable has an excellent bending tolerance of approximatelytimes.
This is because the Sensors may affect each other and cause output chattering even if separated by more than the Sensor sensing distance. Systems, machines, and equipment that could present a risk to life or property.
The axis from the center of the lens to the center of the beam for the Emitter and the axis from the center of the lens to the center of the reception area for the Receiver. Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
Type of noise Noise intrusion path and countermeasure Before countermeasure Noise enters from the noise source through the frame metal. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out the fibers.
It is our practice to change model numbers when published ratings or features are changed, or when signi? Insert a capacitor e. The following are some examples of applications for which particular attention must be given.
Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output Buy from Cross
Insert a shield copper plate between the Sensor and the noise source e. Please know and observe all prohibitions of use applicable to the products. Power line Work Required for Unconnected Leads Unused leads for self-diagnosis outputs or other special functions should be cut and wrapped with insulating tape to prevent contact with other terminals.
AC 2-wire Sensors Example: Use the following methods to attach and remove Fiber Units. However, if the workpieces are close to the Photoelectric Sensors, light from the adjacent Emitter may be received and cause the Sensor to change to the incident light state.
OMRON E3C-VS1G Photoelectric sensor
This catalog omrno protected by copyright and is intended solely for use in conjunction with the product. Power Supply Types An unsmoothed full-wave or half-wave rectifying power supply cannot be used.
The following measures can be taken to avoid mutual interference. When in doubt, special model numbers may be assigned to?
Countermeasure Concept Use a Sensor with the interference prevention function. Separate the noise source and the Sensor to a distance where noise does not affect operation. For the E3S-C, the optical axis and the mechanical axis are the same, so the optical axis can be easily adjusted by aligning omfon mechanical axis. Doing so may result in damage from burning and fire, particularly if the liquid is flammable.
Separate Sensors to distance where interference does not occur. These Sensors are designed for use in applications for sensing workpieces and workers that do not affect safety. If e3c-v1sg Sensor does not operate, check the following points.
Lowering the sensitivity will generally help. Values Given in Typical Examples The data and values given as typical examples are not ratings and performance and do not indicate specified performance.
Dirt should be gently wiped off with a dry cloth. The lens, however, is plastic. Ambient Conditions Do not use this Sensor in the following locations.
Doing so may cause explosion or burning. If the Sensor and the load are connected to separate power supplies, turn ON the Sensor power before turning ON the load power. Mutual Interference Mutual interference is a state where an output is unstable because the Sensors are affected by light from the adjacent Sensors.
Light may enter even if the Sensors are separated by more than the sensing distance. If not grounded, switching noise in the power supply may cause malfunction.