DIN EN ISO 7253 PDF

Buy DIN EN ISO PAINTS AND VARNISHES – DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) from SAI. DIN EN ISO Paints and varnishes – Determination of resistance to neutral salt spray (fog) (ISO ); German version EN ISO Draft standard [WITHDRAWN] DIN ISO – Draft. Paints and varnishes – Determination of resistance to neutral salt spray (fog) (ISO.

Author: Mauzragore Nill
Country: Iraq
Language: English (Spanish)
Genre: Love
Published (Last): 28 April 2005
Pages: 482
PDF File Size: 18.3 Mb
ePub File Size: 4.71 Mb
ISBN: 822-8-94368-836-1
Downloads: 60439
Price: Free* [*Free Regsitration Required]
Uploader: Tekazahn

The size of any object we can test is limited by the capacity of the salt spray chamber.

Weigh the reference specimens to the nearest 1 mg. Protect one face of the reference specimens with a removable coating, for example an adhesive plastic film.

Assessment of degree of rusting DIN EN ISOPaints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 4: The chemical cleaning procedure is preferably performed in repetitive immersions of 5? Remove isoo corrosion products by mechanical and chemical cleaning, as described in ISO? I suggest that izo send some parts out for testing according to the ISO standard to see if they meet the spec.

The lower edge of the reference specimens shall be level with the top of the salt spray collector.

CORROTHERM 610/400

It does not specify the dimensions of test specimens, the exposure period to be used for a particular product, or the interpretation of results. Make any necessary correction by adding hydrochloric acid, sodium hydroxide or sodium bicarbonate solution of analytical grade.

The recommended test duration is: The scribe mark s shall be parallel to the longer edge of the test panel, unless otherwise agreed. Suitable funnels have a diameter of mm, which corresponds to a collecting area of approximately is cm2.

Equivalence between ASTM B-117 vs. ISO 9227 NSS

If you are more concerned with the effect of sunlight, moisture and temperature on the actual surface coating, please refer to our Durability tests. ASTM G Annex A5 Scope and Field Application This is a less severe version of eh standard salt spray tests and is generally regarded as giving a better correlation with outdoor exposure results.

  BS EN ISO 14341 PDF

In this case degradation is due to complex chemical dim between salt and the materials involved. It is recommended to use freshly prepared solution during every procedure for removal of corrosion products. However, for a new examination or for tests with a total duration exceeding 96 h, location permutation of specimens is permitted The pressure should be 98?

Is there any equivalence between this two standards? NOTE For the efficient dissolution of the corrosion products during the immersion step, it is important that the solution is kept stirred. English price group 13 www.

The test duration shall be 48 h. The requirements are the same for all the tests. We require 16 coated panels x mm.

Equivalence between ASTM B vs. ISO NSS

Assessment of degree of cracking DIN EN ISOPaints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 5: Endorsement notice The text of ISO If the coating on the back or edges of the panel differs from that of the coating product under test, it shall have a corrosion resistance greater than that of the coating product under test.

If you need to test paints, coatings etc, you may wish to consider the prohesion test as a possible alternative. As comparative tests, however, salt spray tests are only suitable if the coatings are sufficiently similar in nature. For this reason, this type of specimen should not be tested with other specimens requiring tests of predetermined durations.

Welcome to new Member Olin Epoxy! Then remove the corrosion products by repetitive cleaning as described in ISO This involves subjecting the samples sequentially to prohesion followed by accelerated weathering. Salt spray tests are generally suitable as corrosion protection tests for rapid analysis for discontinuities, pores and damage in organic and inorganic coatings. Subtract this number from the initial mass of the reference specimen prior to testing, and divide the resulting number by the area of the exposed surface of the reference specimen to assess the metal mass loss per square metre of the reference specimen.

Before they are examined, carefully remove the residues of spray solution from their surfaces.

It is often not possible to use results gained from salt spray testing as a comparative guide to the long? Remember that accelerated testing is not a proper indication of real world performance.

  ANNAHAR JOURNAL PDF

Also, the performance of different materials during the test should dn be taken as a direct guide to the corrosion resistance of these materials in service.

Corrosion resistance

Preference shall be given to apparatus that has a means for properly dealing with fog after the test, prior to releasing it from the building for environmental conservation, and for drawing water prior to discharging it to the drainage system. The quantity of liquid paint we needs depends on the method of application. To determine the corrosivity of the tests, reference? What do you want to test? To apply the scratch, use a scratch instrument with a hard tip. After cleaning, rinse the reference specimens with fresh solvent, and then dry them.

The compressed air supplied to the atomizers shall be passed through a filter to remove all traces of oil or solid matter, and the atomizing pressure shall be at an overpressure of 70? Clean the reference specimens carefully, immediately before testing. We can test different size samples if required with maximum dimensions of x x mm. It is often not possible to use results gained from salt spray testing as a comparative guide to the long-term behaviour of different coating systems, as the corrosion stress during these tests differs significantly from the corrosion stresses encountered in practice.

Adjust the pH using the procedures described in 3. The compressed air supplied to the atomizers shall be passed through a filter to remove all traces of oil or solid matter, and the atomizing pressure shall be at an overpressure of 70 kPa 4 to kPa. Sample Requirements The requirements are the same for all the tests. In addition, for quality control purposes, comparison can be made between specimens coated with the same coating.

Nevertheless, the method described gives a means of checking that the comparative quality of a metallic material, with or without corrosion protection, is maintained.