Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Mashicage Malaktilar
Country: Guadeloupe
Language: English (Spanish)
Genre: Marketing
Published (Last): 23 January 2006
Pages: 445
PDF File Size: 14.54 Mb
ePub File Size: 17.73 Mb
ISBN: 528-6-21181-722-2
Downloads: 87241
Price: Free* [*Free Regsitration Required]
Uploader: Vuk

The Cardax FT Cabinet should be installed in a secure, internal location. Cardax FT Controller Documents. The power supply cable must be of sufficient size to ensure that the voltage at the GBUS unit terminals is the recommended 12 Vdc.

The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in catdax A dial-up modem may be used for communication if network communications are not available.

Cardax Ft Controller pdf

The Cabinet door must remain closed for at least one minute for the initialisation of the optical tamper detectors to be completed. Catdax private key or certificate loaded. Changes or modifications not expressly approved by Gallagher Security Management Systems could void the user’s authority to operate this equipment.

Plug-in ModemThe Cardax FT Controller has an on-board connector Serial for a plugin modem part number C which is purchased separately from the Controller Operation of this equipment in a residential area is likely to cause harmful interference in which case the user carrax be required to correct the interference at his own expense.


Standard and High Specis a processing board for an intruder alarm and access control system.

An upgrade of the Controller software via a USB memory stick is complete and the USB drive must be removed for installation to complete. Label each cable as you remove it.

In the event of a catastrophic failure, after approximately 60 seconds the In-Service relay opens. Overview The Gallagher Controllers are intelligent carddax controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Gallagher Command Center.

Purpose of this presentation This presentation introduces: Part number 3E R1 August This picture is not to scale, therefore use the measurements provided.

Cardax Ft Controller 6000pdf

Looking at the Controller it will be obvious that the there is no ethernet activity on either ethernet connection, as the RJ45 connector LEDs will not be operating, and the Controllers run LED will be in 2 flash. Cardax FT Version 5.

The following procedure will ensure that the optical tamper sensors are initialised correctly on power-up. These contacts close when the Controller is powered up, and remain closed until either the power is removed or there is a ‘Catastrophic Failure’. Then, as it has no configuration, it will not connect to the FT server until the primary ethernet link is connected. On startup, the main application is run. This takes approximately 11 seconds, while data is being written to memory.


The Cardax FT Controller integrates much of the functionality of the original Press the Enter key on your keyboard. Assigning an Cardwx address manually via a web browser When the Cardax FT Controller is started reset or power-up with DIP switches 2 and 3 enabled, the Controller uses the following default addresses: The sequence completes fairly quickly but it is important you ensure the LED finishes indicating the “normal running” sequence.

Switch on power to the Cardax FT Controller The cables should stow neatly and be held in place by the cable clamps fitted into the base of the Cabinet.

On-board termination is optional using termination jumpers. The red Run LED flashes in the following sequence: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Published on Oct View 1.

Initialise the Cardax FT Controller The Gallagher Controller is specifically designed to support access controlled doors and integrated intruder alarms. Because this Controller does not incorporate on-board reader connections it provides a cost-effective solution where ‘alarms-only’ is required.