ATMEL 24C04 PDF

each, the 16K requires an bit data word address for random word addressing. WP Pin. Status. Part of the Array Protected. 24C01A. 24C 24C 24C08A. 24C04 EEPROM are available at Mouser Electronics. Mouser offers For: 24C Obsolete. Microchip Technology / Atmel, EEPROM 7 MILS V – 10MS V. Read about ’24C04 Interfacing issue’ on elementcom. Hey there,I am trying to interface the AT24C04 4K EEPROM with Atmega

Author:	Yozshujas Kekora
Country:	Sao Tome and Principe
Language:	English (Spanish)
Genre:	Literature
Published (Last):	10 December 2004
Pages:	146
PDF File Size:	5.58 Mb
ePub File Size:	17.52 Mb
ISBN:	962-2-87591-660-8
Downloads:	90529
Price:	Free* [*Free Regsitration Required]
Uploader:	Temi

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policy2c404 our Terms of Service. However, it doesn’t matter what I set these pins to. This output is from I2C scanner. Is there something else I need to do? Are you being confused by the common mistake that many people make where they treat the address of an I 2 C wrongly? Even the data sheet that you linked can lead to confusion in this regard. In figure 4 they refer to the address as an 8-bit quantity:.

Also be aware that the A0 to A2 pins on the device package are meant to remain static in a design. If a total of eight 24C02’s are used in the design then each of the devices will have these three pins hard strapped in a different combination from the set of b, 2c04, b, b, b, b, b and b.

Writing to a serial EEPROM Atmel 24C04 in Labview – Discussion Forums – National Instruments

When you say that you are “writing” to the pins this does not make clear exactly what you are doing. Normally there is at,el writing to the 24C02 pins. Instead the three bits that you supply out on the interface in the device address field must match the hard strapped values on the pins in order for the device to be selected.

On top of that I have never been sure that it is even possible to dynamically change the atmrl value on the A0, A1 and A2 pins of a 24C02 after it has powered up. A2 are used for creating the address.

The device will not respond to the address that is being set dynamically. It considers the value of the A0,A1 and A2 before the power up and sticks to it till reset. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Home Questions Tags Users Unanswered. Found 8 device s. Check your chips markings. You do not write the addresses; you hardwire them.

TurboJ The chip says the following: Can you explain what hardwiring is? In figure 4 they refer to the address as an 8-bit quantity: In Arduino, the function that does this is digitalWrite. That’s why I said “write”.

Cheap atmel 24c04 deals

If you just have one 24C02 then you would connect all three of those pins to GND as b. Then when you want to write to the part use an address byte of 0xA0 and when you want to read atmwl an address byte of 0xA1. Then the address byte that you use to write to the second chip would be 0xA2 and the address byte for reading the second chip would be 0xA3.

Then the address byte that you use 24f04 write to the third chip would be 0xA4 and the address byte for reading the second chip would be 0xA5. Can’t change the values dynamically.

It will answer to address that was set up before powering up. So for example you keep A0: MaNyYaCk 6 Can you give more information? atmdl

But my suggestion would to directly connect them to ground or VCC for the addressing scheme. Maybe the issue is setting the address after power on.

I will try in about an hour. Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use atkel the website is subject to these policies.