ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
|Published (Last):||23 December 2006|
|PDF File Size:||12.88 Mb|
|ePub File Size:||10.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
This revision of Speci? Last previous edition approved in as A — One bend test shall be made from one end of each coil.
In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. In case of dispute, the offset method of determining yield strength shall be used. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic ashm and components, architectural and structural applications exposed to non-marine atmospheres.
This standard has been approved for use by agencies of the Department of Defense. A number in parentheses indicates the year xstm last reapproval.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Current edition approved Sept. Type L should be wstm in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Types and L cannot be hardened by thermal treatment. However, in the case of dispute, tests shall be made by pressure. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Types and L are weldable by most fusion or resistance welding techniques.
Find out what NKS can do for you.
304 and 304L Stainless Steel
Number of Tests 8. Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides. Your comments are invited either for astj of this standard or for additional standards and should be addressed to ASTM International Headquarters.
C Annealed material that naturally meets mechanical properties may be applied. The noncontrolling factor normally will exceed considerably the speci? The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Maximum unless otherwise indicated. Astj alloys represent an excellent combination of corrosion resistance and fabricability. Permission rights to photocopy the standard may also be secured from the ASTM website www.
Hard Elongation in 2 in. HardC Elongation in 2 in. Material Test Report and Certi? Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld.
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D PSS means plate, strip, sheet. The choice of test method for materials in conditions other than annealed shall be at the option of the seller. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part. Only annealed conditions of grades speci?
Type L LN Originally approved in If filler metal is required, Type is normally used. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications.
Rockwell B 95 95 The values given in parentheses are for information only. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be asgm controlling factor in meeting the properties.
Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? A — 10 Standard Speci? HRC typical L Ann 25 min. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?