AISI S200-07 PDF

editions of the Specification developed by AISI and CSA. AISI: for example, this Specification will be referred as AISI S, where the last. AISI SSERIES FRAMING STANDARDS BUNDLE. This bundle includes 11 documents. (Download). AISI S/S (). AISI S AISI. AISI-S General requirements for residential and commercial construction, prescriptive and engineered design. Examples include member identification.

Author: Kajiktilar Dodal
Country: Bermuda
Language: English (Spanish)
Genre: Politics
Published (Last): 28 February 2010
Pages: 184
PDF File Size: 12.90 Mb
ePub File Size: 18.62 Mb
ISBN: 826-4-63002-270-1
Downloads: 1038
Price: Free* [*Free Regsitration Required]
Uploader: Vudolar

The discrete braces are limited to not greater than 8 feet 2. The method assumes a sheathing strip carries the lateral load via tension field action.

This chapter provides installation requirements previously contained in the various framing standards. For roof or floor diaphragms with a maximum aspect ratio of 4: Sheathing and discrete bracing.

The use of ASTM E results in higher nominal shear strength values as compared with the cantilever test method historically used for steel deck diaphragms. This chapter contains design, manufacturing quality criteria, and installation requirements for cold-formed steel trusses as previously included s2000-07 AISI S The exception applies where the built-up section is seated properly in a track, and the top and bottom end bearing detail of the studs consists of a steel or concrete support with adequate strength and stiffness to preclude relative end slip of the two built-up stud sections.

The other standards addressed such topics as s200-70 code of standard practice, the definition of standard product, and prescriptive design for residential applications.

This new chapter lists applicable AISI test standards for cold-formed steel framing members, connections, and systems. However, AISI S now incorporates an exception for a built-up axial load bearing section comprised of aisk studs oriented back-to-back forming s2000-07 I-shaped cross-section.

  ESCOP MONOGRAPHS PDF

But, why would AISI develop six discrete framing standards as opposed to one design manual? This has been an often asked question by framing design engineers. Format defines design considerations.

Free CFS Publications from the AISI/SMDI Construction Market Council –

This method provides an alternative approach to determine the shear wall strength, especially for those that are outside the limitations of the tested systems. This limitation has been eliminated from AISI S; however, it should be remembered that mils is still the maximum thickness of standard products in the United States and 97 mils 0. Section reference table S and previous standard. From tothe AISI Committee on Framing Standards developed nine different framing standards to cover specific aspects of cold-formed steel framing.

Effective strip method model for steel-sheet sheathing.

Free CFS Publications from the AISI/SMDI Construction Market Council

Six of these standards addressed the design of structural elements, such as general provisions, wall studs, floor joists, trusses, headers, and shear walls. This new exception provides for a more economical built-up member, as is often used as a jamb stud or shear wall boundary member.

This newly developed chapter provides minimum requirements for quality control aisk quality assurance for material control and installation for cold-formed steel light-frame construction.

This computational method is applicable for walls sheathed with steel sheet. This chapter contains design provisions for aixi steel framing members and assemblies, as previously included in AISI S, S, S, and S For curtain wall systems, the standard now permits the use of the bracing combination of sheathing attached to one side of the wall stud and discrete bracing for the other flange Figure 1.

The previous design standards limited their application to framing members having a maximum base steel thickness to mils 0. The truss component structural performance load test and full-scale truss confirmatory test methods, previously included in AISI S, are provided in this appendix.

  FISICA TIPLER MOSCA VOL 2 PDF

ASTM C has historically stipulated manufacturing tolerances for aiso steel structural framing members. The chapter also includes:. Inthe manufacturing tolerance values were extended to the flange width and stiffening lip length. Your message Submit Comment.

It outlines the scope, which is for design and installation of cold-formed steel framing of a floor and roof systems, b structural walls, c shear walls, strap braced walls, and diaphragms to resist in-plane lateral loads, and d trusses for load-carrying purposes in buildings.

This appendix contains requirements for the determination of the rotational stiffness that structural sheathing provides to framing members to facilitate the design for distortional buckling.

These cold-formed steel framing standards are available as free downloads at www. First Name Last Name. The simple reason is, it was easier to develop small single-topic documents versus a more comprehensive multi-topic document. This new standard includes design provisions for wall systems, floor and roof systems, lateral force-resisting systems, as well as truss and header assemblies.

Leave a Comment Click here to cancel reply. This article focuses on AISI S which applies to cold-formed steel structural members subject to gravity loading, wind loading, and seismic loading, except when specific seismic detailing is required.

The effective strip method is permitted to be used within the following range of parameters:. Also, for ease of use, S contains a section reference table between the S provisions and the previous provisions Table 2.