74193 IC PDF

The DM74LS circuit is a synchronous up/down 4-bit binary counter. Synchronous operation is provided by hav- ing all flip-flops clocked simultaneously. 74LS, 74LS Datasheet, 74LS Binary Up/Down Counter Datasheet, buy 74LS D1, 1 •, 16, Vcc. Q1, 2, 15, D0. Q0, 3, 14, MR. CPD, 4, 13, TCD. CPU, 5, 12, TCU. Q2, 6, 11, PL. Q3, 7, 10, D2. GND, 8, 9, D3.

Author: Bragis Daikinos
Country: Eritrea
Language: English (Spanish)
Genre: Sex
Published (Last): 26 March 2009
Pages: 13
PDF File Size: 16.70 Mb
ePub File Size: 15.51 Mb
ISBN: 882-3-44051-160-8
Downloads: 15612
Price: Free* [*Free Regsitration Required]
Uploader: Mezicage

Forums New posts Search forums. Please note that I made a mistake in the video and said the circuit uses a but it actually uses a 74LS IC.

A counter chip comes with a fair number of features on it. Analyze the counter shown below to determine the counters lower and upper count limit. The biggest disadvantage of the 74LS is that it can only count up as I stated above. Let’s have a look at the different pins. For Example on the 6-to up counter you see the inverter on Q0 and you would calculate the maximum count would be on 14 E but since the pulse goes through the asynchronous input and it is counting up, it subtracts a 1 from 14 and this is why the count ends at The Asynchronous load subtracts a number i makes the maximum count The first thing we had to modify from the previous counter was to wire the clock to the up count input of the 74LS The reason it can count is that the Chip has a Up and Down input and depending on which input u put it, is how the clock will count.


What are the advantages of implementing a synchronous counter with the 74LS 741993 circuit versus using discrete flip-flops and gates?

This is the 2-to-9 Binary Up Counter. Pioneer Elite vsxtx water damage no power Started by Watin Today at Replacement Transformer Started by ncag Today at 7: The way it works is pretty simple. As always, it’s a good idea to tie any input pins we don’t want to use to GND. It works according to the design and the probes show the binary count that goes into the HEX display.

Are there any disadvantages to using the 74LS integrated circuit? The thing that makes it so much better than the is that the chip has uc capacity to count both up and down.

IC, SN , 4-bit binary up/down counter

These are the four output pins. The probes show the binary count that go into the HEX Display. For a better experience, please enable JavaScript in your browser before proceeding.

In order to use the ‘, you will have to decode the 10 count and use it to clock the next id and reset the first stage. It has been bread boarded based on the Multisim design. When the DOWN pin gets a rising edge clock pulse, the flops count down by one number.


I’d would not go with the because it counts in binary. Use the 74LS to create a Binary up counter. This is a Clear pin, which will instantly reset all the outputs to LOW, or 0.

2x IC SN74193N Counter Up/down 4 Bit Binary 16 Pin Plastic DIP

After you have made the circuit modify the circuit to count from E. By continuing to use this site, you are consenting to our use of cookies. They signal when the counter is about to reset. Since ix counters are readily available as cheap IC’s, we’ll move straight on to talk about how jc use a counter chip.

As we learned the has a input called a load and it is loaded with a binary count from the ABCD Inputs.

Terminal count up pin 12 connects to clock pulse up pin 5 of the next stage. An advantage of using the 74LS IC over using discrete flip flops and gates is that every thing is dramatically simplified.

Datasheets, Manuals or Parts. When UP gets a rising edge clock pulse, it makes the internal flops count up by one number. Thread starter lhanx2 Start date Dec 16, This is the 4-to Binary Up Counter Video.